Get our all latest and free stuff by subscribing to your youtube channel for FREE. 

ConcreteConstruction Industry

How to get burn marks off Concrete? (Simple 5 steps)

Burn marks on concrete can be unsightly and difficult to remove. However, with the right tools and techniques, you can easily remove burn marks from your concrete surfaces.

As a homeowner, I recently had a fire incident on my concrete driveway that left unsightly burn marks. I was extremely annoyed and frustrated, but I knew I had to do something about it. I didn’t want to spend a lot of money on professional cleaning services, so I decided to try a few different methods using simple, home-available products.

Here are the steps to take to remove burn marks from concrete:

Table of Contents

Pressure wash

Start by cleaning the concrete surface. Use a broom or a leaf blower to remove any debris or dirt from the surface. Then, use a pressure washer to clean the concrete thoroughly. This will ensure that the surface is free of any dirt or debris that may interfere with the removal process.

Using wire brush

Next, use a wire brush to scrub the burn marks. This step is crucial as it helps to loosen any debris or stains that may be stuck to the concrete. Use a stiff-bristled brush to scrub the burn marks in a circular motion. Be sure to apply enough pressure to remove the burn marks but not so much that you damage the concrete.

Concrete cleaner

If the burn marks are still present after scrubbing, use a concrete cleaner or degreaser to remove them. These products are specifically designed to remove stains and marks from concrete surfaces. Follow the instructions on the product label and apply it to the burn marks. Allow it to sit for the recommended amount of time before rinsing the surface with a pressure washer.

Chemical Concrete Etcher

If the burn marks are still present, you can use a chemical concrete etcher. This is a stronger solution that is designed to remove stubborn stains from concrete surfaces. Be sure to follow the instructions on the product label and wear protective gear when using it. Apply the etcher to the burn marks and allow it to sit for the recommended amount of time before rinsing the surface with a pressure washer.

Once you have removed the burn marks, rinse the surface with clean water and let it dry completely. Once dry, you can seal the concrete to protect it from future stains or marks.

It’s important to note that, depending on the severity of the burn marks and the age of the concrete, some burn marks may be impossible to remove completely. In such cases, it’s best to consult with a professional.

Also Read: Dry Lean Concrete (DLC) full form

Using Powder dish detergent

One method for removing burn marks from concrete is by using a powdered dish detergent. Here are the steps for this method:

  1. Start by cleaning the concrete surface. Use a broom or a leaf blower to remove any debris or dirt from the surface. Then, use a pressure washer to clean the concrete thoroughly. This will ensure that the surface is free of any dirt or debris that may interfere with the removal process.
  2. Next, mix a small amount of powdered dish detergent with warm water to create a paste. The paste should be thick enough to stick to the burn marks without running off.
  3. Apply the paste to the burn marks using a stiff-bristled brush. Scrub the burn marks in a circular motion, applying enough pressure to remove the burn marks but not so much that you damage the concrete. Be sure to pay extra attention to the edges of the burn marks.
  4. Allow the paste to sit for about 10-15 minutes, or as recommended by the dish detergent.
  5. After the paste has sat for the recommended amount of time, use a pressure washer to rinse the surface thoroughly. This will remove any remaining paste and debris from the burn marks.
  6. Once the surface is clean and dry, you can seal the concrete to protect it from future stains or marks.

Also Read: What Paint Do You Use for a Concrete Water Fountain?

Using liquid dish soap

Another method for removing burn marks from concrete is by using liquid dish soap. Here are the steps for this method:

  1. Start by cleaning the concrete surface. Use a broom or a leaf blower to remove any debris or dirt from the surface. Then, use a pressure washer to clean the concrete thoroughly. This will ensure that the surface is free of any dirt or debris that may interfere with the removal process.
  2. Next, mix a small amount of liquid dish soap with warm water in a spray bottle. Spray the solution directly onto the burn marks.
  3. Use a stiff-bristled brush to scrub the burn marks in a circular motion, applying enough pressure to remove the burn marks but not so much that you damage the concrete. Be sure to pay extra attention to the edges of the burn marks.
  4. Allow the solution to sit for about 10-15 minutes, or as recommended by the dish soap.
  5. After the solution has sat for the recommended amount of time, use a pressure washer to rinse the surface thoroughly. This will remove any remaining solution and debris from the burn marks.
  6. Once the surface is clean and dry, you can seal the concrete to protect it from future stains or marks.

Using Baking Soda Method

The baking soda method is another way to remove burn marks from concrete. Here are the steps for this method:

  1. Start by cleaning the concrete surface. Use a broom or a leaf blower to remove any debris or dirt from the surface. Then, use a pressure washer to clean the concrete thoroughly. This will ensure that the surface is free of any dirt or debris that may interfere with the removal process.
  2. Next, mix baking soda and water together to make a paste. The paste should be thick enough to stick to the burn marks without running off.
  3. Apply the paste to the burn marks using a stiff-bristled brush. Scrub the burn marks in a circular motion, applying enough pressure to remove the burn marks but not so much that you damage the concrete. Be sure to pay extra attention to the edges of the burn marks.
  4. Allow the paste to sit for about 10-15 minutes.
  5. After the paste has sat for the recommended amount of time, use a pressure washer to rinse the surface thoroughly. This will remove any remaining paste and debris from the burn marks.
  6. Once the surface is clean and dry, you can seal the concrete to protect it from future stains or marks.

Also Read: 5 Tips for Maintaining Your Concrete Swimming Pool

MethodProsCons
Pressure Washer Method– Quick and easy method for cleaning the surface– High pressure can cause damage to the concrete if not used carefully
Powdered Dish Detergent Method– Effective in removing burn marks– Can be time-consuming if the burn marks are severe
Liquid Dish Soap Method– Quick and easy method for applying the cleaning solution– May not be as effective as other methods for removing burn marks
Baking Soda Method– Effective in removing burn marks– Can be time-consuming if the burn marks are severe

Conclusion

In summary, removing burn marks from concrete requires cleaning the surface, scrubbing with a wire brush, using a concrete cleaner or degreaser, using a chemical concrete etcher, and sealing the surface. With proper care and maintenance, you can keep your concrete surfaces looking like new.

About author

Saad is a civil engineer by profession and love to explore innovative ideas relevant to construction, civil engineering, and home improvement. He loves writing about concrete, DIY guides, home improvement tips, technologies, and more.
    Related posts
    Construction IndustryTerminologies

    Chipping meaning in Construction and Civil Engineering – Steps

    Construction IndustryTerminologies

    EGL meaning in Civil Engineering and Construction

    ConcreteConstruction Industry

    The right Driveway paving Contractor near me

    Construction IndustryTerminologies

    Wet weather flow and dry weather flow in Wastewater design – Differences - Calculation

    Sign up for our Newsletter and
    stay informed

    Leave a Reply

    Your email address will not be published. Required fields are marked *